| Activity |
IDVSD |
| Part Number |
ATV212HU30N4 |
| ambient air temperature for storage |
-25-70 °C |
| depth |
150 mm |
| device short name |
ATV212 |
| dielectric strength |
3535 V DC between earth and power terminals, 5092 V DC between control and power terminals |
| height |
184 mm |
| IP degree of protection |
IP21 |
| marking |
CE |
| minimum switching current |
3 mA at 24 V DC for configurable relay logic |
| motor power hp |
4 hp |
| motor power kW |
3 kW |
| motor starter type |
variable speed drive |
| net weight |
3.35 kg |
| network frequency |
47.5...63 Hz |
| power range |
2.2-3 kW at 380-440 V 3 phases, 2.2-3 kW at 480-500 V 3 phases |
| supply voltage limits |
323-528 V |
| tightening torque |
1.3 N.m, 11.5 lb.in (L1/R, L2/S, L3/T), 0.6 N.m (VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES) |
| width |
142 mm |
| Assembly style |
with heat sink |
| Supply frequency |
50...60 Hz - 5...5 % |
| Supply |
internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, <10 A, protection type: overload and short-circuit protection, internal supply: 24 V DC (21-27 V), <200 A, protection type: overload and short-circuit protection |
| Continuous output current |
7.2 A at 380 V, 7.2 A at 460 V |
| Discrete input type |
F programmable 24 V DC, with level 1 PLC, impedance: 4700 Ohm, R programmable 24 V DC, with level 1 PLC, impedance: 4700 Ohm, RES programmable 24 V DC, with level 1 PLC, impedance: 4700 Ohm |
| Analogue input number |
2 |
| Analogue input type |
VIA switch-configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 10 bits, VIB configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 10 bits, VIB configurable PTC probe: 0...6 probes, impedance: 1500 Ohm, VIA switch-configurable current: 0...20 mA, impedance: 250 Ohm, resolution 10 bits |
| Discrete output type |
configurable relay logic: (FLA, FLC) NO - 100000 cycles, configurable relay logic: (FLB, FLC) NC - 100000 cycles, configurable relay logic: (RY, RC) NO - 100000 cycles |
| Maximum switching current |
5 A at 250 V AC on resistive load - cos phi = 1 - L/R = 0 ms (FL, R), 5 A at 30 V DC on resistive load - cos phi = 1 - L/R = 0 ms (FL, R), 2 A at 250 V AC on inductive load - cos phi = 0.4 - L/R = 7 ms (FL, R), 2 A at 30 V DC on inductive load - cos phi = 0.4 - L/R = 7 ms (FL, R) |
| Functionality |
mid |
| Analogue output number |
1 |
| Discrete output number |
2 |
| Discrete input logic |
positive logic (source) (F, R, RES), <= 5 V (state 0), >= 11 V (state 1), negative logic (sink) (F, R, RES), >= 16 V (state 0), <= 10 V (state 1) |
| Accuracy |
+/- 0.6 % (VIA) for a temperature variation 60 °C, +/- 0.6 % (VIB) for a temperature variation 60 °C, +/- 1 % (FM) for a temperature variation 60 °C |
| Transmission rate |
9600 bps or 19200 bps |
| Analogue output type |
FM switch-configurable voltage 0...10 V DC, impedance: 7620 Ohm, resolution 10 bits, FM switch-configurable current 0...20 mA, impedance: 970 Ohm, resolution 10 bits |
| Sampling duration |
2 ms +/- 0.5 ms F discrete, 2 ms +/- 0.5 ms R discrete, 2 ms +/- 0.5 ms RES discrete, 3.5 ms +/- 0.5 ms VIA analog, 22 ms +/- 0.5 ms VIB analog |
| Prospective line Isc |
5 kA |
| Asynchronous motor control profile |
voltage/frequency ratio, 2 points, voltage/frequency ratio, 5 points, voltage/frequency ratio, automatic IR compensation (U/f + automatic Uo), voltage/frequency ratio - Energy Saving, quadratic U/f, flux vector control without sensor, standard |
| Apparent power |
5.5 kVA at 380 V |
| Type of polarization |
no impedance |
| Frequency resolution |
display unit: 0.1 Hz, analog input: 0.024/50 Hz |
| Motor slip compensation |
adjustable, automatic whatever the load, not available in voltage/frequency ratio motor control |
| Regulation loop |
adjustable PI regulator |
| Number of addresses |
1-247 |
| Speed range |
01-Oct |
| Linearity error |
VIA: +/- 0.15 % of maximum value for input, VIB: +/- 0.15 % of maximum value for input, FM: +/- 0.2 % for output |
| Specific application |
HVAC |
| Air flow |
47 m3/h |
| Discrete and process manufacturing |
building - HVAC compressor for scroll, building - HVAC fan, building - HVAC pump |
| Option card |
communication card for LonWorks |
| Acceleration and deceleration ramps |
automatic based on the load, linear adjustable separately from 0.01 to 3200 s |
| Speed drive output frequency |
0.5-200 Hz |
| Transmission frame |
RTU |
| Torque accuracy |
+/- 15 % |
| Communication service |
write multiple registers (16) 2 words maximum, read holding registers (03) 2 words maximum, time out setting from 0.1 to 100 s, read device identification (43), monitoring inhibitable, write single register (06) |
| Transient overtorque |
120-120 % of nominal motor torque +/- 10 % for 60 s |
| Data format |
8 bits, 1 stop, odd even or no configurable parity |
| Maximum transient current |
7.9 A for 60 s |
| Line current |
4.9 A at 480 V, 6.2 A at 380 V |
| Isolation |
electrical between power and control |
| Nominal switching frequency |
12 kHz |
| EMC filter |
Class C2 EMC filter integrated |
| Braking to standstill |
by DC injection |
| Speed accuracy |
+/- 10 % of nominal slip 0.2 Tn to Tn |
| vibration resistance |
1.5 mm (f= 3-13 Hz) conforming to EN/IEC 60068-2-6, 1 gn (f= 13-200 Hz) conforming to EN/IEC 60068-2-8 |
| electromagnetic compatibility |
electrostatic discharge immunity test level 3 conforming to IEC 61000-4-2, radiated radio-frequency electromagnetic field immunity test level 3 conforming to IEC 61000-4-3, electrical fast transient/burst immunity test level 4 conforming to IEC 61000-4-4, 1.2/50 µs - 8/20 µs surge immunity test level 3 conforming to IEC 61000-4-5, conducted radio-frequency immunity test level 3 conforming to IEC 61000-4-6, voltage dips and interruptions immunity test conforming to IEC 61000-4-11 |
| ambient air temperature for operation |
-10-40 °C (without derating), 40-50 °C (with derating factor) |
| standards |
IEC 61800-3 environments 1 category C3, EN 61800-3 environments 1 category C3, EN 61800-3 environments 2 category C3, EN 61800-3 category C2, IEC 61800-3 environments 2 category C2, IEC 61800-3 environments 2 category C1, EN 61800-3 category C3, IEC 61800-3 category C3, IEC 61800-3 environments 1 category C2, IEC 61800-3, EN 61800-5-1, EN 55011 class A group 1, EN 61800-3 environments 2 category C1, EN 61800-3, IEC 61800-3 category C2, IEC 61800-3 environments 2 category C3, IEC 61800-5-1, UL Type 1, EN 61800-3 environments 1 category C2, EN 61800-3 environments 2 category C2, IEC 61800-3 environments 1 category C1, EN 61800-3 environments 1 category C1 |
| local signalling |
1 LED (red) for DC bus energized |
| environmental characteristic |
classes 3C1 conforming to IEC 60721-3-3, classes 3S2 conforming to IEC 60721-3-3 |
| insulation resistance |
>= 1 mOhm 500 V DC for 1 minute |
| Electrical Connection |
VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES: terminal 2.5-2.5 mm² / AWG 14, L1/R, L2/S, L3/T: terminal 6-6 mm² / AWG 10 |
| Network Number of Phases |
3 phases |
| Communication Port Protocol |
METASYS N2, LonWorks, Modbus, BACnet, APOGEE FLN |
| Type of Cable |
without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 90 °C / XLPE/EPR, without mounting kit: 1 wire(s)IEC cable at 45 °C, copper 70 °C / PVC, with UL Type 1 kit: 3 wire(s)UL 508 cable at 40 °C, copper 75 °C / PVC |
| Connector Type |
1 open style, 1 RJ45 |
| Noise Level |
51 dB conforming to 86/188/EEC |
| Switching Frequency |
6...16 kHz adjustable, 12...16 kHz with derating factor |
